Cisco

venggovi@cisco.com

Cisco

svenaas@cisco.com

Routing Internet Engineering Task Force template This document specifies an update to the PIM Receiver RLOC Join/ Prune attribute that supports the construction of multicast distribution trees where the root and receivers are located in different Locator/ID Separation Protocol (LISP) sites and are connected using underlay IP Multicast. This attribute allows the receiver site to signal the underlay multicast group to the control plane of the root Ingress Tunnel Router (ITR).

Introduction The construction of multicast distribution trees where the root and receivers are located in different LISP sites is defined in . specifies that (root-EID, G) data packets are to be LISP- encapsulated into (root-RLOC, G) multicast packets. defines PIM J/P attribute extensions to construct multicast distribution trees. This document extends the Receiver ETR RLOC PIM J/P attribute to facilitate the construction of underlay multicast trees for (root-RLOC, G). Specifically, the assignment of the underlay multicast group needs to be done in consonance with the downstream xTR nodes and avoid unnecessary replication or traffic hairpinning. Since the Receiver RLOC Attribute defined in only addresses the Ingress Replication case, an extension of the scope of that PIM J/P attribute is defined by this draft to include scenarios where the underlay uses Multicast transport. The scope extension proposed here complies with the base specification . This document uses terminology defined in , such as EID, RLOC, ITR, and ETR.

Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119.

When LISP based Multicast trees can be built using IP Multicast in the underlay, the mapping between the overlay group address and the underlay group address becomes a very crucial engineering decision:

Flexible mapping of overlay to underlay group ranges:

Three different types of overlay to underlay group mappings are possible: Many to one mapping: Many (root-EID, G) flows originating from a RLOC can be mapped to the same underlay (root-RLOC, G-u) flow. One to many mapping: Conversely the same overlay flow can be mapped to two or more flows e.g. (root-RLOC, G-u1) and (root-RLOC, G-u2) to cater to the requirements of downstream xTR nodes. One to one mapping: Every (root-EID, G) flow is mapped to a different (root-RLOC, G-u) flow.

Multicast Address Range constraints:

It is possible that under certain circumstances, differnt subsets of xTRs subscribing to the same overlay multicast stream would be constrained to use different underlay multicast mapping ranges. This definitely involves a trade-off between replication and the flexibility in assigning address ranges and could be required in certain situations further below.

Inter-site PxTR:

When multiple LISP sites are connected through a LISP based transit, the site border node interconnects the site-facing interfaces and the external LISP based core. Under such circumstances, there could be different ranges of multicast group addresses used for building the (S-RLOC, G) trees inside the LISP site and the external LISP based core. This is desired for various reasons:

Hardware resource restrictions:

Platform limitations could force engineering decisions to be made on restricting multicast address ranges in the underlay.

There are no changes proposed to the syntax and semantics of the Transport attributed defined in RFC8059. The scope of the updates proposed to RFC 8059 are limited to the case where the "Transport" field of the Transport Attribute is set to zero (Multicast) only.

The definition of the "Receiver RLOC" field of the Receiver ETR RLOC attribute RFC 8059 is updated as follows:

Receiver RLOC:

The Receiver RLOC field of the Receiver RLOC Attribute MAY contain a multicast IP address. This MUST be used only when the underlay network of the LISP core supports IP Multicast transport.

The definitions of the other fields of the Receiver ETR RLOC Attribute remain unchanged. When the ITR needs to track the list of ETRs from which the PIM joins are received, the ITR MUST use the source IP address field of the incoming PIM Join/ Prune. The source IP of the PIM Join/ Prune MUST be an ETR RLOC IP address.

When the ETR determines to use the multicast underlay:

• It chooses an underlay multicast group that it can join. This is a matter of local decision, beyond the scope of this document.
• It identifies the upstream LISP site where the underlay multicast tree tree needs to be rooted.
• It constructs the PIM Join/ Prune message as specified in RFC 8059. Only the Receiver RLOC attribute is encoded as above.

When the ITR receives a PIM Join/ Prune message:

• It allocates a new entry in the oif-list for every unique underlay multicast mapping.
• The ITR MAY apply local policy to perform any kind of rate-limiting on the number of copies it needs to make in the underlay. Such actions are beyond the scope of this document.

Acknowledgements The authors would like to thank Dino Farinacci, Victor Moreno, Alvaro Retana and Aswin Kuppusami for their valuable comments. The authors also thank Sankaralingam T and Amit Kumar for their contributions to the document.

IANA Considerations No new requests to IANA.

Security Considerations There is perhaps a new attack vector where an attacker can send a bunch of joins with different group addresses. It may interfere with other multicast traffic if those group addresses overlap. Also, it may take up a lot of resources if replication for thousands of groups are requested. However PIM authentication could be used here. Since explicit tracking could be done, an implementation may consider knobs to ensure that for each ETR RLOC (the RLOC used as the source of the overlay join), there could be a configurable number of maximum permissible group(s).