Synonymous Flow Label Framework

Synonymous Flow Label Framework Futurewei Technologies Inc.

sb@stewartbryant.com

Huawei

mach.chen@huawei.com

Southend Technical Center

swallow.ietf@gmail.com

Ciena Corporation

ssivabal@ciena.com

ZTE Corp.

gregimirsky@gmail.com

Routing MPLS MPLS Flow Label RFC 8372 ("MPLS Flow Identification Considerations") describes the requirement for introducing flow identities within the MPLS architecture. This document describes a method of accomplishing this by using a technique called "Synonymous Flow Labels" in which labels that mimic the behavior of other labels provide the identification service. These identifiers can be used to trigger per-flow operations on the packet at the receiving label switching router.

Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at .

Copyright Notice Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents () in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

Table of Contents

. Introduction
. Requirements Language
. Synonymous Flow Labels
. User Service Traffic in the Data Plane
- . Application Label Present
  - . Setting TTL and the Traffic Class Bits
- . Single-Label Stack
  - . Setting TTL and the Traffic Class Bits
- . Aggregation of SFL Actions
. Equal-Cost Multipath Considerations
. Privacy Considerations
. Security Considerations
. IANA Considerations
. References
- . Normative References
- . Informative References
Contributors
Authors' Addresses

Introduction ("MPLS Flow Identification Considerations") describes the requirement for introducing flow identities within the MPLS architecture. This document describes a method of providing the required identification by using a technique called "Synonymous Flow Labels (SFLs)" in which labels that mimic the behavior of other MPLS labels provide the identification service. These identifiers can be used to trigger per-flow operations on the packet at the receiving label switching router.

Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here.

Synonymous Flow Labels An SFL is defined to be a label that causes exactly the same behavior at the egress Label Edge Router (LER) as the label it replaces, except that it also causes one or more additional actions that have been previously agreed between the peer LERs to be executed on the packet. There are many possible additional actions, such as measuring the number of received packets in a flow, triggering an IP Flow Information Export (IPFIX) capture, triggering other types of deep packet inspection, or identifying the packet source. For example, in a Performance Monitoring (PM) application, the agreed action could be recording the receipt of the packet by incrementing a packet counter. This is a natural action in many MPLS implementations, and where supported, this permits the implementation of high-quality packet loss measurement without any change to the packet-forwarding system. To illustrate the use of this technology, we start by considering the case where there is an application label in the MPLS label stack. As a first example, let us consider a pseudowire (PW) on which it is desired to make packet loss measurements. Two labels, synonymous with the PW labels, are obtained from the egress terminating provider edge (T-PE). By alternating between these SFLs and using them in place of the PW label, the PW packets may be batched for counting without any impact on the PW forwarding behavior (note that strictly only one SFL is needed in this application, but that is an optimization that is a matter for the implementor). The method of obtaining these additional labels is outside the scope of this text; however, one control protocol that provides a method of obtaining SFLs is described in . Next, consider an MPLS application that is multipoint to point, such as a VPN. Here, it is necessary to identify a packet batch from a specific source. This is achieved by making the SFLs source specific, so that batches from one source are marked differently from batches from another source. The sources all operate independently and asynchronously from each other, independently coordinating with the destination. Each ingress LER is thus able to establish its own SFL to identify the subflow and thus enable PM per flow. Finally, we need to consider the case where there is no MPLS application label such as occurs when sending IP over a Label Switched Path (LSP), i.e., there is a single label in the MPLS label stack. In this case, introducing an SFL that was synonymous with the LSP label would introduce network-wide forwarding state. This would not be acceptable for scaling reasons. Therefore, we have no choice but to introduce an additional label. Where penultimate hop popping (PHP) is in use, the semantics of this additional label can be similar to the LSP label. Where PHP is not in use, the semantics are similar to an MPLS Explicit NULL . In both of these cases, the label has the additional semantics of the SFL. Note that to achieve the goals set out above, SFLs need to be allocated from the platform label table.

User Service Traffic in the Data Plane As noted in , it is necessary to consider two cases:

Application label is present
Single-label stack

Application Label Present shows the case in which both an LSP label and an application label are present in the MPLS label stack. Traffic with no SFL function present runs over the normal stack, and SFL-enabled flows run over the SFL stack with the SFL used to indicate the packet batch.

Setting TTL and the Traffic Class Bits The TTL and the Traffic Class bits in the SFL label stack entry (LSE) would normally be set to the same value as would have been set in the label that the SFL is synonymous with. However, it is recognized that, if there is an application need, these fields in the SFL LSE MAY be set to some other value. An example would be where it was desired to cause the SFL to trigger an action in the TTL expiry exception path as part of the label action.

Single-Label Stack shows the case in which only an LSP label is present in the MPLS label stack. Traffic with no SFL function present runs over the "normal" stack, and SFL-enabled flows run over the SFL stack with the SFL used to indicate the packet batch. However, in this case, it is necessary for the ingress Label Edge Router (LER) to first push the SFL and then to push the LSP label.

Where the LSP label is still present
Where the LSP label is penultimate hop popped

If the LSP label is present, it is processed exactly as it would normally be processed, and then it is popped. This reveals the SFL, which, in the case of the measurements defined in , is simply counted and then discarded. In this respect, the processing of the SFL is synonymous with an MPLS Explicit NULL. As the SFL is the bottom of stack, the IP packet that follows is processed as normal. If the LSP label is not present due to PHP action in the upstream LSR, two almost equivalent processing actions can take place. The SFL can be treated either 1) as an LSP label that was not PHPed and the additional associated SFL action is taken when the label is processed or 2) as an MPLS Explicit NULL with associated SFL actions. From the perspective of the measurement system described in this document, the behavior of the two approaches is indistinguishable; thus, either may be implemented.

Setting TTL and the Traffic Class Bits The TTL and the Traffic Class considerations described in apply.

Aggregation of SFL Actions There are cases where it is desirable to aggregate an SFL action against a number of labels, for example, where it is desirable to have one counter record the number of packets received over a group of application labels or where the number of labels used by a single application is large and the resultant increase in the number of allocated labels needed to support the SFL actions may become too large to be viable. In these circumstances, it would be necessary to introduce an additional label in the stack to act as an aggregate instruction. This is not strictly a synonymous action in that the SFL is not replacing an existing label but is somewhat similar to the single-label case shown in , and the same signaling, management, and configuration tools would be applicable.

Aggregate SFL Actions +-----------------+ | LSP | | Label | | (May be PHPed) | +-----------------+ +-----------------+ | LSP | | | | Label | | Aggregate | | (May be PHPed) | | SFL | +-----------------+ +-----------------+ | | | | | Application | | Application | | Label | | Label | +-----------------+ <=BoS +-----------------+ <= Bottom of Stack | | | | | Payload | | Payload | | | | | +-----------------+ +-----------------+ "Normal" Label Stack Label Stack with SFL The aggregate SFL is shown in the label stack depicted in as preceding the application label; however, the choice of position before or after the application label will be application specific. In the case described in , by definition, the SFL has the full application context. In this case, the positioning will depend on whether the SFL action needs the full context of the application to perform its action and whether the complexity of the application will be increased by finding an SFL following the application label.

Equal-Cost Multipath Considerations The introduction of an SFL to an existing flow may cause that flow to take a different path through the network under conditions of Equal-Cost Multipath (ECMP). This, in turn, may invalidate certain uses of the SFL, such as performance measurement applications. Where this is a problem, there are two solutions worthy of consideration:

The operator MAY elect to always run with the SFL in place in the MPLS label stack.
The operator can elect to use entropy labels in a network that fully supports this type of ECMP. If this approach is adopted, the intervening MPLS network MUST NOT load balance on any packet field other than the entropy label. Note that this is stricter than the text in .

Privacy Considerations IETF concerns on pervasive monitoring are described in . The inclusion of originating and/or flow information in a packet provides more identity information and hence potentially degrades the privacy of the communication to an attacker in a position to observe the added identifier. Whilst the inclusion of the additional granularity does allow greater insight into the flow characteristics, it does not specifically identify which node originated the packet unless the attacker can inspect the network at the point of ingress or inspect the control protocol packets. This privacy threat may be mitigated by encrypting the control protocol packets by regularly changing the synonymous labels or by concurrently using a number of such labels, including the use of a combination of those methods. Minimizing the scope of the identity indication can be useful in minimizing the observability of the flow characteristics. Whenever IPFIX or other deep packet inspection (DPI) technique is used, their relevant privacy considerations apply.

Security Considerations There are no new security issues associated with the MPLS data plane. Any control protocol used to request SFLs will need to ensure the legitimacy of the request, i.e., that the requesting node is authorized to make that SFL request by the network operator.

IANA Considerations This document has no IANA actions.

References Normative References Key words for use in RFCs to Indicate Requirement Levels In many standards track documents several words are used to signify the requirements in the specification. These words are often capitalized. This document defines these words as they should be interpreted in IETF documents. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements. MPLS Label Stack Encoding This document specifies the encoding to be used by an LSR in order to transmit labeled packets on Point-to-Point Protocol (PPP) data links, on LAN data links, and possibly on other data links as well. This document also specifies rules and procedures for processing the various fields of the label stack encoding. [STANDARDS-TRACK] Multiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field The early Multiprotocol Label Switching (MPLS) documents defined the form of the MPLS label stack entry. This includes a three-bit field called the "EXP field". The exact use of this field was not defined by these documents, except to state that it was to be "reserved for experimental use". Although the intended use of the EXP field was as a "Class of Service" (CoS) field, it was not named a CoS field by these early documents because the use of such a CoS field was not considered to be sufficiently defined. Today a number of standards documents define its usage as a CoS field. To avoid misunderstanding about how this field may be used, it has become increasingly necessary to rename this field. This document changes the name of the field to the "Traffic Class field" ("TC field"). In doing so, it also updates documents that define the current use of the EXP field. [STANDARDS-TRACK] The Use of Entropy Labels in MPLS Forwarding Load balancing is a powerful tool for engineering traffic across a network. This memo suggests ways of improving load balancing across MPLS networks using the concept of "entropy labels". It defines the concept, describes why entropy labels are useful, enumerates properties of entropy labels that allow maximal benefit, and shows how they can be signaled and used for various applications. This document updates RFCs 3031, 3107, 3209, and 5036. [STANDARDS-TRACK] Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words RFC 2119 specifies common key words that may be used in protocol specifications. This document aims to reduce the ambiguity by clarifying that only UPPERCASE usage of the key words have the defined special meanings. Informative References A Simple Control Protocol for MPLS SFLs Futurewei Technologies Inc. Southend Technical Center Ciena Corporation In draft-ietf-mpls-sfl-framework the concept of MPLS synonymous flow labels (SFL) was introduced. This document describes a simple control protocol that runs over an associated control header to request, withdraw, and extend the lifetime of such labels. It is not the only control protocol that moght be used to support SFL, but it has the benefit of being able to be used without modifying of the existing MPLS control prodocols. The existance of this design is not intended to restrict the ability to enhance an existing MPLS control protocol to add a similar capability. A Querier MUST wait a configured time (suggested wait of 60 seconds) before re-attempting a Withdraw request. No more than three Withdraw requests SHOULD be made. These restricctions are to prevent overloading the control plane of the actioning router. Work in Progress Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture This document describes an architecture for Pseudo Wire Emulation Edge-to-Edge (PWE3). It discusses the emulation of services such as Frame Relay, ATM, Ethernet, TDM, and SONET/SDH over packet switched networks (PSNs) using IP or MPLS. It presents the architectural framework for pseudo wires (PWs), defines terminology, and specifies the various protocol elements and their functions. This memo provides information for the Internet community. Packet Loss and Delay Measurement for MPLS Networks Many service provider service level agreements (SLAs) depend on the ability to measure and monitor performance metrics for packet loss and one-way and two-way delay, as well as related metrics such as delay variation and channel throughput. This measurement capability also provides operators with greater visibility into the performance characteristics of their networks, thereby facilitating planning, troubleshooting, and network performance evaluation. This document specifies protocol mechanisms to enable the efficient and accurate measurement of these performance metrics in MPLS networks. [STANDARDS-TRACK] Specification of the IP Flow Information Export (IPFIX) Protocol for the Exchange of Flow Information This document specifies the IP Flow Information Export (IPFIX) protocol, which serves as a means for transmitting Traffic Flow information over the network. In order to transmit Traffic Flow information from an Exporting Process to a Collecting Process, a common representation of flow data and a standard means of communicating them are required. This document describes how the IPFIX Data and Template Records are carried over a number of transport protocols from an IPFIX Exporting Process to an IPFIX Collecting Process. This document obsoletes RFC 5101. Pervasive Monitoring Is an Attack Pervasive monitoring is a technical attack that should be mitigated in the design of IETF protocols, where possible. Alternate-Marking Method for Passive and Hybrid Performance Monitoring This document describes a method to perform packet loss, delay, and jitter measurements on live traffic. This method is based on an Alternate-Marking (coloring) technique. A report is provided in order to explain an example and show the method applicability. This technology can be applied in various situations, as detailed in this document, and could be considered Passive or Hybrid depending on the application. MPLS Flow Identification Considerations This document discusses aspects to consider when developing a solution for MPLS flow identification. The key application that needs this solution is in-band performance monitoring of MPLS flows when MPLS is used to encapsulate user data packets.

Contributors Huawei

lizhenbin@huawei.com

Authors' Addresses Futurewei Technologies Inc.