An update for kernel is now available for openEuler-22.03-LTS-SP1 Security Advisory openeuler-security@openeuler.org openEuler security committee openEuler-SA-2024-2031 Final 1.0 1.0 2024-08-23 Initial 2024-08-23 2024-08-23 openEuler SA Tool V1.0 2024-08-23 kernel security update An update for kernel is now available for openEuler-22.03-LTS-SP1 The Linux Kernel, the operating system core itself. Security Fix(es): In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_acl_tcam: Fix stack corruption When tc filters are first added to a net device, the corresponding local port gets bound to an ACL group in the device. The group contains a list of ACLs. In turn, each ACL points to a different TCAM region where the filters are stored. During forwarding, the ACLs are sequentially evaluated until a match is found. One reason to place filters in different regions is when they are added with decreasing priorities and in an alternating order so that two consecutive filters can never fit in the same region because of their key usage. In Spectrum-2 and newer ASICs the firmware started to report that the maximum number of ACLs in a group is more than 16, but the layout of the register that configures ACL groups (PAGT) was not updated to account for that. It is therefore possible to hit stack corruption [1] in the rare case where more than 16 ACLs in a group are required. Fix by limiting the maximum ACL group size to the minimum between what the firmware reports and the maximum ACLs that fit in the PAGT register. Add a test case to make sure the machine does not crash when this condition is hit. [1] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120 [...] dump_stack_lvl+0x36/0x50 panic+0x305/0x330 __stack_chk_fail+0x15/0x20 mlxsw_sp_acl_tcam_group_update+0x116/0x120 mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110 mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0 mlxsw_sp_acl_rule_add+0x47/0x240 mlxsw_sp_flower_replace+0x1a9/0x1d0 tc_setup_cb_add+0xdc/0x1c0 fl_hw_replace_filter+0x146/0x1f0 fl_change+0xc17/0x1360 tc_new_tfilter+0x472/0xb90 rtnetlink_rcv_msg+0x313/0x3b0 netlink_rcv_skb+0x58/0x100 netlink_unicast+0x244/0x390 netlink_sendmsg+0x1e4/0x440 ____sys_sendmsg+0x164/0x260 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xc0 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x63/0x6b(CVE-2024-26586) In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache There is a potential UAF scenario in the case of an LPI translation cache hit racing with an operation that invalidates the cache, such as a DISCARD ITS command. The root of the problem is that vgic_its_check_cache() does not elevate the refcount on the vgic_irq before dropping the lock that serializes refcount changes. Have vgic_its_check_cache() raise the refcount on the returned vgic_irq and add the corresponding decrement after queueing the interrupt.(CVE-2024-26598) In the Linux kernel, the following vulnerability has been resolved: net: relax socket state check at accept time. Christoph reported the following splat: WARNING: CPU: 1 PID: 772 at net/ipv4/af_inet.c:761 __inet_accept+0x1f4/0x4a0 Modules linked in: CPU: 1 PID: 772 Comm: syz-executor510 Not tainted 6.9.0-rc7-g7da7119fe22b #56 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 RIP: 0010:__inet_accept+0x1f4/0x4a0 net/ipv4/af_inet.c:759 Code: 04 38 84 c0 0f 85 87 00 00 00 41 c7 04 24 03 00 00 00 48 83 c4 10 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 ec b7 da fd <0f> 0b e9 7f fe ff ff e8 e0 b7 da fd 0f 0b e9 fe fe ff ff 89 d9 80 RSP: 0018:ffffc90000c2fc58 EFLAGS: 00010293 RAX: ffffffff836bdd14 RBX: 0000000000000000 RCX: ffff888104668000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: dffffc0000000000 R08: ffffffff836bdb89 R09: fffff52000185f64 R10: dffffc0000000000 R11: fffff52000185f64 R12: dffffc0000000000 R13: 1ffff92000185f98 R14: ffff88810754d880 R15: ffff8881007b7800 FS: 000000001c772880(0000) GS:ffff88811b280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fb9fcf2e178 CR3: 00000001045d2002 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> inet_accept+0x138/0x1d0 net/ipv4/af_inet.c:786 do_accept+0x435/0x620 net/socket.c:1929 __sys_accept4_file net/socket.c:1969 [inline] __sys_accept4+0x9b/0x110 net/socket.c:1999 __do_sys_accept net/socket.c:2016 [inline] __se_sys_accept net/socket.c:2013 [inline] __x64_sys_accept+0x7d/0x90 net/socket.c:2013 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x58/0x100 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x4315f9 Code: fd ff 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 ab b4 fd ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffdb26d9c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002b RAX: ffffffffffffffda RBX: 0000000000400300 RCX: 00000000004315f9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000004 RBP: 00000000006e1018 R08: 0000000000400300 R09: 0000000000400300 R10: 0000000000400300 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000040cdf0 R14: 000000000040ce80 R15: 0000000000000055 </TASK> The reproducer invokes shutdown() before entering the listener status. After commit 94062790aedb ("tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets"), the above causes the child to reach the accept syscall in FIN_WAIT1 status. Eric noted we can relax the existing assertion in __inet_accept()(CVE-2024-36484) In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: add missing firmware sanity checks Add the missing sanity checks when parsing the firmware files before downloading them to avoid accessing and corrupting memory beyond the vmalloced buffer.(CVE-2024-36880) In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when devlink reload during initialization The devlink reload process will access the hardware resources, but the register operation is done before the hardware is initialized. So, processing the devlink reload during initialization may lead to kernel crash. This patch fixes this by registering the devlink after hardware initialization.(CVE-2024-36900) In the Linux kernel, the following vulnerability has been resolved: tcp: Use refcount_inc_not_zero() in tcp_twsk_unique(). Anderson Nascimento reported a use-after-free splat in tcp_twsk_unique() with nice analysis. Since commit ec94c2696f0b ("tcp/dccp: avoid one atomic operation for timewait hashdance"), inet_twsk_hashdance() sets TIME-WAIT socket's sk_refcnt after putting it into ehash and releasing the bucket lock. Thus, there is a small race window where other threads could try to reuse the port during connect() and call sock_hold() in tcp_twsk_unique() for the TIME-WAIT socket with zero refcnt. If that happens, the refcnt taken by tcp_twsk_unique() is overwritten and sock_put() will cause underflow, triggering a real use-after-free somewhere else. To avoid the use-after-free, we need to use refcount_inc_not_zero() in tcp_twsk_unique() and give up on reusing the port if it returns false. [0]: refcount_t: addition on 0; use-after-free. WARNING: CPU: 0 PID: 1039313 at lib/refcount.c:25 refcount_warn_saturate+0xe5/0x110 CPU: 0 PID: 1039313 Comm: trigger Not tainted 6.8.6-200.fc39.x86_64 #1 Hardware name: VMware, Inc. VMware20,1/440BX Desktop Reference Platform, BIOS VMW201.00V.21805430.B64.2305221830 05/22/2023 RIP: 0010:refcount_warn_saturate+0xe5/0x110 Code: 42 8e ff 0f 0b c3 cc cc cc cc 80 3d aa 13 ea 01 00 0f 85 5e ff ff ff 48 c7 c7 f8 8e b7 82 c6 05 96 13 ea 01 01 e8 7b 42 8e ff <0f> 0b c3 cc cc cc cc 48 c7 c7 50 8f b7 82 c6 05 7a 13 ea 01 01 e8 RSP: 0018:ffffc90006b43b60 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff888009bb3ef0 RCX: 0000000000000027 RDX: ffff88807be218c8 RSI: 0000000000000001 RDI: ffff88807be218c0 RBP: 0000000000069d70 R08: 0000000000000000 R09: ffffc90006b439f0 R10: ffffc90006b439e8 R11: 0000000000000003 R12: ffff8880029ede84 R13: 0000000000004e20 R14: ffffffff84356dc0 R15: ffff888009bb3ef0 FS: 00007f62c10926c0(0000) GS:ffff88807be00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020ccb000 CR3: 000000004628c005 CR4: 0000000000f70ef0 PKRU: 55555554 Call Trace: <TASK> ? refcount_warn_saturate+0xe5/0x110 ? __warn+0x81/0x130 ? refcount_warn_saturate+0xe5/0x110 ? report_bug+0x171/0x1a0 ? refcount_warn_saturate+0xe5/0x110 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? refcount_warn_saturate+0xe5/0x110 tcp_twsk_unique+0x186/0x190 __inet_check_established+0x176/0x2d0 __inet_hash_connect+0x74/0x7d0 ? __pfx___inet_check_established+0x10/0x10 tcp_v4_connect+0x278/0x530 __inet_stream_connect+0x10f/0x3d0 inet_stream_connect+0x3a/0x60 __sys_connect+0xa8/0xd0 __x64_sys_connect+0x18/0x20 do_syscall_64+0x83/0x170 entry_SYSCALL_64_after_hwframe+0x78/0x80 RIP: 0033:0x7f62c11a885d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a3 45 0c 00 f7 d8 64 89 01 48 RSP: 002b:00007f62c1091e58 EFLAGS: 00000296 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000020ccb004 RCX: 00007f62c11a885d RDX: 0000000000000010 RSI: 0000000020ccb000 RDI: 0000000000000003 RBP: 00007f62c1091e90 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000296 R12: 00007f62c10926c0 R13: ffffffffffffff88 R14: 0000000000000000 R15: 00007ffe237885b0 </TASK>(CVE-2024-36904) In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Skip on writeback when it's not applicable [WHY] dynamic memory safety error detector (KASAN) catches and generates error messages "BUG: KASAN: slab-out-of-bounds" as writeback connector does not support certain features which are not initialized. [HOW] Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.(CVE-2024-36914) In the Linux kernel, the following vulnerability has been resolved: nsh: Restore skb->{protocol,data,mac_header} for outer header in nsh_gso_segment(). syzbot triggered various splats (see [0] and links) by a crafted GSO packet of VIRTIO_NET_HDR_GSO_UDP layering the following protocols: ETH_P_8021AD + ETH_P_NSH + ETH_P_IPV6 + IPPROTO_UDP NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls skb_mac_gso_segment() to invoke inner protocol GSO handlers. nsh_gso_segment() does the following for the original skb before calling skb_mac_gso_segment() 1. reset skb->network_header 2. save the original skb->{mac_heaeder,mac_len} in a local variable 3. pull the NSH header 4. resets skb->mac_header 5. set up skb->mac_len and skb->protocol for the inner protocol. and does the following for the segmented skb 6. set ntohs(ETH_P_NSH) to skb->protocol 7. push the NSH header 8. restore skb->mac_header 9. set skb->mac_header + mac_len to skb->network_header 10. restore skb->mac_len There are two problems in 6-7 and 8-9. (a) After 6 & 7, skb->data points to the NSH header, so the outer header (ETH_P_8021AD in this case) is stripped when skb is sent out of netdev. Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH), skb_pull() in the first nsh_gso_segment() will make skb->data point to the middle of the outer NSH or Ethernet header because the Ethernet header is not pulled by the second nsh_gso_segment(). (b) While restoring skb->{mac_header,network_header} in 8 & 9, nsh_gso_segment() does not assume that the data in the linear buffer is shifted. However, udp6_ufo_fragment() could shift the data and change skb->mac_header accordingly as demonstrated by syzbot. If this happens, even the restored skb->mac_header points to the middle of the outer header. It seems nsh_gso_segment() has never worked with outer headers so far. At the end of nsh_gso_segment(), the outer header must be restored for the segmented skb, instead of the NSH header. To do that, let's calculate the outer header position relatively from the inner header and set skb->{data,mac_header,protocol} properly. [0]: BUG: KMSAN: uninit-value in ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline] BUG: KMSAN: uninit-value in ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline] BUG: KMSAN: uninit-value in ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668 ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline] ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668 ipvlan_start_xmit+0x5c/0x1a0 drivers/net/ipvlan/ipvlan_main.c:222 __netdev_start_xmit include/linux/netdevice.h:4989 [inline] netdev_start_xmit include/linux/netdevice.h:5003 [inline] xmit_one net/core/dev.c:3547 [inline] dev_hard_start_xmit+0x244/0xa10 net/core/dev.c:3563 __dev_queue_xmit+0x33ed/0x51c0 net/core/dev.c:4351 dev_queue_xmit include/linux/netdevice.h:3171 [inline] packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook mm/slub.c:3819 [inline] slab_alloc_node mm/slub.c:3860 [inline] __do_kmalloc_node mm/slub.c:3980 [inline] __kmalloc_node_track_caller+0x705/0x1000 mm/slub.c:4001 kmalloc_reserve+0x249/0x4a0 net/core/skbuff.c:582 __ ---truncated---(CVE-2024-36933) In the Linux kernel, the following vulnerability has been resolved: bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue Fix NULL pointer data-races in sk_psock_skb_ingress_enqueue() which syzbot reported [1]. [1] BUG: KCSAN: data-race in sk_psock_drop / sk_psock_skb_ingress_enqueue write to 0xffff88814b3278b8 of 8 bytes by task 10724 on cpu 1: sk_psock_stop_verdict net/core/skmsg.c:1257 [inline] sk_psock_drop+0x13e/0x1f0 net/core/skmsg.c:843 sk_psock_put include/linux/skmsg.h:459 [inline] sock_map_close+0x1a7/0x260 net/core/sock_map.c:1648 unix_release+0x4b/0x80 net/unix/af_unix.c:1048 __sock_release net/socket.c:659 [inline] sock_close+0x68/0x150 net/socket.c:1421 __fput+0x2c1/0x660 fs/file_table.c:422 __fput_sync+0x44/0x60 fs/file_table.c:507 __do_sys_close fs/open.c:1556 [inline] __se_sys_close+0x101/0x1b0 fs/open.c:1541 __x64_sys_close+0x1f/0x30 fs/open.c:1541 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 read to 0xffff88814b3278b8 of 8 bytes by task 10713 on cpu 0: sk_psock_data_ready include/linux/skmsg.h:464 [inline] sk_psock_skb_ingress_enqueue+0x32d/0x390 net/core/skmsg.c:555 sk_psock_skb_ingress_self+0x185/0x1e0 net/core/skmsg.c:606 sk_psock_verdict_apply net/core/skmsg.c:1008 [inline] sk_psock_verdict_recv+0x3e4/0x4a0 net/core/skmsg.c:1202 unix_read_skb net/unix/af_unix.c:2546 [inline] unix_stream_read_skb+0x9e/0xf0 net/unix/af_unix.c:2682 sk_psock_verdict_data_ready+0x77/0x220 net/core/skmsg.c:1223 unix_stream_sendmsg+0x527/0x860 net/unix/af_unix.c:2339 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x140/0x180 net/socket.c:745 ____sys_sendmsg+0x312/0x410 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x1e9/0x280 net/socket.c:2667 __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x46/0x50 net/socket.c:2674 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 value changed: 0xffffffff83d7feb0 -> 0x0000000000000000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 Prior to this, commit 4cd12c6065df ("bpf, sockmap: Fix NULL pointer dereference in sk_psock_verdict_data_ready()") fixed one NULL pointer similarly due to no protection of saved_data_ready. Here is another different caller causing the same issue because of the same reason. So we should protect it with sk_callback_lock read lock because the writer side in the sk_psock_drop() uses "write_lock_bh(&sk->sk_callback_lock);". To avoid errors that could happen in future, I move those two pairs of lock into the sk_psock_data_ready(), which is suggested by John Fastabend.(CVE-2024-36938) In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix seg fault in rxe_comp_queue_pkt In rxe_comp_queue_pkt() an incoming response packet skb is enqueued to the resp_pkts queue and then a decision is made whether to run the completer task inline or schedule it. Finally the skb is dereferenced to bump a 'hw' performance counter. This is wrong because if the completer task is already running in a separate thread it may have already processed the skb and freed it which can cause a seg fault. This has been observed infrequently in testing at high scale. This patch fixes this by changing the order of enqueuing the packet until after the counter is accessed.(CVE-2024-38544) In the Linux kernel, the following vulnerability has been resolved: eth: sungem: remove .ndo_poll_controller to avoid deadlocks Erhard reports netpoll warnings from sungem: netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398) WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c gem_poll_controller() disables interrupts, which may sleep. We can't sleep in netpoll, it has interrupts disabled completely. Strangely, gem_poll_controller() doesn't even poll the completions, and instead acts as if an interrupt has fired so it just schedules NAPI and exits. None of this has been necessary for years, since netpoll invokes NAPI directly.(CVE-2024-38597) In the Linux kernel, the following vulnerability has been resolved: ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find() Syzbot reports a warning as follows: ============================================ WARNING: CPU: 0 PID: 5075 at fs/mbcache.c:419 mb_cache_destroy+0x224/0x290 Modules linked in: CPU: 0 PID: 5075 Comm: syz-executor199 Not tainted 6.9.0-rc6-gb947cc5bf6d7 RIP: 0010:mb_cache_destroy+0x224/0x290 fs/mbcache.c:419 Call Trace: <TASK> ext4_put_super+0x6d4/0xcd0 fs/ext4/super.c:1375 generic_shutdown_super+0x136/0x2d0 fs/super.c:641 kill_block_super+0x44/0x90 fs/super.c:1675 ext4_kill_sb+0x68/0xa0 fs/ext4/super.c:7327 [...] ============================================ This is because when finding an entry in ext4_xattr_block_cache_find(), if ext4_sb_bread() returns -ENOMEM, the ce's e_refcnt, which has already grown in the __entry_find(), won't be put away, and eventually trigger the above issue in mb_cache_destroy() due to reference count leakage. So call mb_cache_entry_put() on the -ENOMEM error branch as a quick fix.(CVE-2024-39276) In the Linux kernel, the following vulnerability has been resolved: jfs: xattr: fix buffer overflow for invalid xattr When an xattr size is not what is expected, it is printed out to the kernel log in hex format as a form of debugging. But when that xattr size is bigger than the expected size, printing it out can cause an access off the end of the buffer. Fix this all up by properly restricting the size of the debug hex dump in the kernel log.(CVE-2024-40902) In the Linux kernel, the following vulnerability has been resolved: tty: add the option to have a tty reject a new ldisc ... and use it to limit the virtual terminals to just N_TTY. They are kind of special, and in particular, the "con_write()" routine violates the "writes cannot sleep" rule that some ldiscs rely on. This avoids the BUG: sleeping function called from invalid context at kernel/printk/printk.c:2659 when N_GSM has been attached to a virtual console, and gsmld_write() calls con_write() while holding a spinlock, and con_write() then tries to get the console lock.(CVE-2024-40966) In the Linux kernel, the following vulnerability has been resolved: ibmvnic: Add tx check to prevent skb leak Below is a summary of how the driver stores a reference to an skb during transmit: tx_buff[free_map[consumer_index]]->skb = new_skb; free_map[consumer_index] = IBMVNIC_INVALID_MAP; consumer_index ++; Where variable data looks like this: free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3] consumer_index^ tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null] The driver has checks to ensure that free_map[consumer_index] pointed to a valid index but there was no check to ensure that this index pointed to an unused/null skb address. So, if, by some chance, our free_map and tx_buff lists become out of sync then we were previously risking an skb memory leak. This could then cause tcp congestion control to stop sending packets, eventually leading to ETIMEDOUT. Therefore, add a conditional to ensure that the skb address is null. If not then warn the user (because this is still a bug that should be patched) and free the old pointer to prevent memleak/tcp problems.(CVE-2024-41066) In the Linux kernel, the following vulnerability has been resolved: nvme: avoid double free special payload If a discard request needs to be retried, and that retry may fail before a new special payload is added, a double free will result. Clear the RQF_SPECIAL_LOAD when the request is cleaned.(CVE-2024-41073) In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Fix double free on error If e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jump to the err_out label, which will call devres_release_group(). devres_release_group() will trigger a call to ata_host_release(). ata_host_release() calls kfree(host), so executing the kfree(host) in ata_host_alloc() will lead to a double free: kernel BUG at mm/slub.c:553! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:kfree+0x2cf/0x2f0 Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 da RSP: 0018:ffffc90000f377f0 EFLAGS: 00010246 RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320 RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0 RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000 R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780 R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006 FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? die+0x2e/0x50 ? do_trap+0xca/0x110 ? do_error_trap+0x6a/0x90 ? kfree+0x2cf/0x2f0 ? exc_invalid_op+0x50/0x70 ? kfree+0x2cf/0x2f0 ? asm_exc_invalid_op+0x1a/0x20 ? ata_host_alloc+0xf5/0x120 [libata] ? ata_host_alloc+0xf5/0x120 [libata] ? kfree+0x2cf/0x2f0 ata_host_alloc+0xf5/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci] Ensure that we will not call kfree(host) twice, by performing the kfree() only if the devres_open_group() call failed.(CVE-2024-41087) In the Linux kernel, the following vulnerability has been resolved: can: mcp251xfd: fix infinite loop when xmit fails When the mcp251xfd_start_xmit() function fails, the driver stops processing messages, and the interrupt routine does not return, running indefinitely even after killing the running application. Error messages: [ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16 [ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3). ... and repeat forever. The issue can be triggered when multiple devices share the same SPI interface. And there is concurrent access to the bus. The problem occurs because tx_ring->head increments even if mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX package while still expecting a response in mcp251xfd_handle_tefif_one(). Resolve the issue by starting a workqueue to write the tx obj synchronously if err = -EBUSY. In case of another error, decrement tx_ring->head, remove skb from the echo stack, and drop the message. [mkl: use more imperative wording in patch description](CVE-2024-41088) In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers register store validation for NFT_DATA_VALUE is conditional, however, the datatype is always either NFT_DATA_VALUE or NFT_DATA_VERDICT. This only requires a new helper function to infer the register type from the set datatype so this conditional check can be removed. Otherwise, pointer to chain object can be leaked through the registers.(CVE-2024-42070) In the Linux kernel, the following vulnerability has been resolved: powerpc: Avoid nmi_enter/nmi_exit in real mode interrupt. nmi_enter()/nmi_exit() touches per cpu variables which can lead to kernel crash when invoked during real mode interrupt handling (e.g. early HMI/MCE interrupt handler) if percpu allocation comes from vmalloc area. Early HMI/MCE handlers are called through DEFINE_INTERRUPT_HANDLER_NMI() wrapper which invokes nmi_enter/nmi_exit calls. We don't see any issue when percpu allocation is from the embedded first chunk. However with CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK enabled there are chances where percpu allocation can come from the vmalloc area. With kernel command line "percpu_alloc=page" we can force percpu allocation to come from vmalloc area and can see kernel crash in machine_check_early: [ 1.215714] NIP [c000000000e49eb4] rcu_nmi_enter+0x24/0x110 [ 1.215717] LR [c0000000000461a0] machine_check_early+0xf0/0x2c0 [ 1.215719] --- interrupt: 200 [ 1.215720] [c000000fffd73180] [0000000000000000] 0x0 (unreliable) [ 1.215722] [c000000fffd731b0] [0000000000000000] 0x0 [ 1.215724] [c000000fffd73210] [c000000000008364] machine_check_early_common+0x134/0x1f8 Fix this by avoiding use of nmi_enter()/nmi_exit() in real mode if percpu first chunk is not embedded.(CVE-2024-42126) In the Linux kernel, the following vulnerability has been resolved: drm/lima: fix shared irq handling on driver remove lima uses a shared interrupt, so the interrupt handlers must be prepared to be called at any time. At driver removal time, the clocks are disabled early and the interrupts stay registered until the very end of the remove process due to the devm usage. This is potentially a bug as the interrupts access device registers which assumes clocks are enabled. A crash can be triggered by removing the driver in a kernel with CONFIG_DEBUG_SHIRQ enabled. This patch frees the interrupts at each lima device finishing callback so that the handlers are already unregistered by the time we fully disable clocks.(CVE-2024-42127) In the Linux kernel, the following vulnerability has been resolved: mm: avoid overflows in dirty throttling logic The dirty throttling logic is interspersed with assumptions that dirty limits in PAGE_SIZE units fit into 32-bit (so that various multiplications fit into 64-bits). If limits end up being larger, we will hit overflows, possible divisions by 0 etc. Fix these problems by never allowing so large dirty limits as they have dubious practical value anyway. For dirty_bytes / dirty_background_bytes interfaces we can just refuse to set so large limits. For dirty_ratio / dirty_background_ratio it isn't so simple as the dirty limit is computed from the amount of available memory which can change due to memory hotplug etc. So when converting dirty limits from ratios to numbers of pages, we just don't allow the result to exceed UINT_MAX. This is root-only triggerable problem which occurs when the operator sets dirty limits to >16 TB.(CVE-2024-42131) In the Linux kernel, the following vulnerability has been resolved: libceph: fix race between delayed_work() and ceph_monc_stop() The way the delayed work is handled in ceph_monc_stop() is prone to races with mon_fault() and possibly also finish_hunting(). Both of these can requeue the delayed work which wouldn't be canceled by any of the following code in case that happens after cancel_delayed_work_sync() runs -- __close_session() doesn't mess with the delayed work in order to avoid interfering with the hunting interval logic. This part was missed in commit b5d91704f53e ("libceph: behave in mon_fault() if cur_mon < 0") and use-after-free can still ensue on monc and objects that hang off of it, with monc->auth and monc->monmap being particularly susceptible to quickly being reused. To fix this: - clear monc->cur_mon and monc->hunting as part of closing the session in ceph_monc_stop() - bail from delayed_work() if monc->cur_mon is cleared, similar to how it's done in mon_fault() and finish_hunting() (based on monc->hunting) - call cancel_delayed_work_sync() after the session is closed(CVE-2024-42232) In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: Prevent OOB read/write in usb_string_copy() Userspace provided string 's' could trivially have the length zero. Left unchecked this will firstly result in an OOB read in the form `if (str[0 - 1] == '\n') followed closely by an OOB write in the form `str[0 - 1] = '\0'`. There is already a validating check to catch strings that are too long. Let's supply an additional check for invalid strings that are too short.(CVE-2024-42236) In the Linux kernel, the following vulnerability has been resolved: ext4: make sure the first directory block is not a hole The syzbot constructs a directory that has no dirblock but is non-inline, i.e. the first directory block is a hole. And no errors are reported when creating files in this directory in the following flow. ext4_mknod ... ext4_add_entry // Read block 0 ext4_read_dirblock(dir, block, DIRENT) bh = ext4_bread(NULL, inode, block, 0) if (!bh && (type == INDEX || type == DIRENT_HTREE)) // The first directory block is a hole // But type == DIRENT, so no error is reported. After that, we get a directory block without '.' and '..' but with a valid dentry. This may cause some code that relies on dot or dotdot (such as make_indexed_dir()) to crash. Therefore when ext4_read_dirblock() finds that the first directory block is a hole report that the filesystem is corrupted and return an error to avoid loading corrupted data from disk causing something bad.(CVE-2024-42304) In the Linux kernel, the following vulnerability has been resolved: drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes In cdv_intel_lvds_get_modes(), the return value of drm_mode_duplicate() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_mode_duplicate(). Add a check to avoid npd.(CVE-2024-42310) In the Linux kernel, the following vulnerability has been resolved: bna: adjust 'name' buf size of bna_tcb and bna_ccb structures To have enough space to write all possible sprintf() args. Currently 'name' size is 16, but the first '%s' specifier may already need at least 16 characters, since 'bnad->netdev->name' is used there. For '%d' specifiers, assume that they require: * 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8 * 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX is 16 And replace sprintf with snprintf. Detected using the static analysis tool - Svace.(CVE-2024-43839) An update for kernel is now available for openEuler-22.03-LTS-SP1. openEuler Security has rated this update as having a security impact of high. A Common Vunlnerability Scoring System(CVSS)base score,which gives a detailed severity rating, is available for each vulnerability from the CVElink(s) in the References section. High kernel https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-26586 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-26598 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36484 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36880 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36900 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36904 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36914 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36933 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-36938 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-38544 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-38597 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-39276 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-40902 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-40966 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-41066 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-41073 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-41087 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-41088 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42070 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42126 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42127 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42131 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42232 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42236 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42304 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-42310 https://www.openeuler.org/en/security/cve/detail/?cveId=CVE-2024-43839 https://nvd.nist.gov/vuln/detail/CVE-2024-26586 https://nvd.nist.gov/vuln/detail/CVE-2024-26598 https://nvd.nist.gov/vuln/detail/CVE-2024-36484 https://nvd.nist.gov/vuln/detail/CVE-2024-36880 https://nvd.nist.gov/vuln/detail/CVE-2024-36900 https://nvd.nist.gov/vuln/detail/CVE-2024-36904 https://nvd.nist.gov/vuln/detail/CVE-2024-36914 https://nvd.nist.gov/vuln/detail/CVE-2024-36933 https://nvd.nist.gov/vuln/detail/CVE-2024-36938 https://nvd.nist.gov/vuln/detail/CVE-2024-38544 https://nvd.nist.gov/vuln/detail/CVE-2024-38597 https://nvd.nist.gov/vuln/detail/CVE-2024-39276 https://nvd.nist.gov/vuln/detail/CVE-2024-40902 https://nvd.nist.gov/vuln/detail/CVE-2024-40966 https://nvd.nist.gov/vuln/detail/CVE-2024-41066 https://nvd.nist.gov/vuln/detail/CVE-2024-41073 https://nvd.nist.gov/vuln/detail/CVE-2024-41087 https://nvd.nist.gov/vuln/detail/CVE-2024-41088 https://nvd.nist.gov/vuln/detail/CVE-2024-42070 https://nvd.nist.gov/vuln/detail/CVE-2024-42126 https://nvd.nist.gov/vuln/detail/CVE-2024-42127 https://nvd.nist.gov/vuln/detail/CVE-2024-42131 https://nvd.nist.gov/vuln/detail/CVE-2024-42232 https://nvd.nist.gov/vuln/detail/CVE-2024-42236 https://nvd.nist.gov/vuln/detail/CVE-2024-42304 https://nvd.nist.gov/vuln/detail/CVE-2024-42310 https://nvd.nist.gov/vuln/detail/CVE-2024-43839 openEuler-22.03-LTS-SP1 kernel-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-debuginfo-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-debugsource-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-devel-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-headers-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-source-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-tools-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-tools-debuginfo-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-tools-devel-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm perf-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm perf-debuginfo-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm python3-perf-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm python3-perf-debuginfo-5.10.0-136.90.0.171.oe2203sp1.aarch64.rpm kernel-5.10.0-136.90.0.171.oe2203sp1.src.rpm kernel-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-debuginfo-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-debugsource-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-devel-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-headers-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-source-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-tools-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-tools-debuginfo-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm kernel-tools-devel-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm perf-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm perf-debuginfo-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm python3-perf-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm python3-perf-debuginfo-5.10.0-136.90.0.171.oe2203sp1.x86_64.rpm In the Linux kernel, the following vulnerability has been resolved:mlxsw: spectrum_acl_tcam: Fix stack corruptionWhen tc filters are first added to a net device, the corresponding localport gets bound to an ACL group in the device. The group contains a listof ACLs. In turn, each ACL points to a different TCAM region where thefilters are stored. During forwarding, the ACLs are sequentiallyevaluated until a match is found.One reason to place filters in different regions is when they are addedwith decreasing priorities and in an alternating order so that twoconsecutive filters can never fit in the same region because of theirkey usage.In Spectrum-2 and newer ASICs the firmware started to report that themaximum number of ACLs in a group is more than 16, but the layout of theregister that configures ACL groups (PAGT) was not updated to accountfor that. It is therefore possible to hit stack corruption [1] in therare case where more than 16 ACLs in a group are required.Fix by limiting the maximum ACL group size to the minimum between whatthe firmware reports and the maximum ACLs that fit in the PAGT register.Add a test case to make sure the machine does not crash when thiscondition is hit.[1]Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120[...] dump_stack_lvl+0x36/0x50 panic+0x305/0x330 __stack_chk_fail+0x15/0x20 mlxsw_sp_acl_tcam_group_update+0x116/0x120 mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110 mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0 mlxsw_sp_acl_rule_add+0x47/0x240 mlxsw_sp_flower_replace+0x1a9/0x1d0 tc_setup_cb_add+0xdc/0x1c0 fl_hw_replace_filter+0x146/0x1f0 fl_change+0xc17/0x1360 tc_new_tfilter+0x472/0xb90 rtnetlink_rcv_msg+0x313/0x3b0 netlink_rcv_skb+0x58/0x100 netlink_unicast+0x244/0x390 netlink_sendmsg+0x1e4/0x440 ____sys_sendmsg+0x164/0x260 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xc0 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x63/0x6b 2024-08-23 CVE-2024-26586 openEuler-22.03-LTS-SP1 Medium 6.7 AV:L/AC:L/PR:H/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved:KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cacheThere is a potential UAF scenario in the case of an LPI translationcache hit racing with an operation that invalidates the cache, suchas a DISCARD ITS command. The root of the problem is thatvgic_its_check_cache() does not elevate the refcount on the vgic_irqbefore dropping the lock that serializes refcount changes.Have vgic_its_check_cache() raise the refcount on the returned vgic_irqand add the corresponding decrement after queueing the interrupt. 2024-08-23 CVE-2024-26598 openEuler-22.03-LTS-SP1 High 7.8 AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: net: relax socket state check at accept time. Christoph reported the following splat: WARNING: CPU: 1 PID: 772 at net/ipv4/af_inet.c:761 __inet_accept+0x1f4/0x4a0 Modules linked in: CPU: 1 PID: 772 Comm: syz-executor510 Not tainted 6.9.0-rc7-g7da7119fe22b #56 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 RIP: 0010:__inet_accept+0x1f4/0x4a0 net/ipv4/af_inet.c:759 Code: 04 38 84 c0 0f 85 87 00 00 00 41 c7 04 24 03 00 00 00 48 83 c4 10 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 ec b7 da fd <0f> 0b e9 7f fe ff ff e8 e0 b7 da fd 0f 0b e9 fe fe ff ff 89 d9 80 RSP: 0018:ffffc90000c2fc58 EFLAGS: 00010293 RAX: ffffffff836bdd14 RBX: 0000000000000000 RCX: ffff888104668000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: dffffc0000000000 R08: ffffffff836bdb89 R09: fffff52000185f64 R10: dffffc0000000000 R11: fffff52000185f64 R12: dffffc0000000000 R13: 1ffff92000185f98 R14: ffff88810754d880 R15: ffff8881007b7800 FS: 000000001c772880(0000) GS:ffff88811b280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fb9fcf2e178 CR3: 00000001045d2002 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> inet_accept+0x138/0x1d0 net/ipv4/af_inet.c:786 do_accept+0x435/0x620 net/socket.c:1929 __sys_accept4_file net/socket.c:1969 [inline] __sys_accept4+0x9b/0x110 net/socket.c:1999 __do_sys_accept net/socket.c:2016 [inline] __se_sys_accept net/socket.c:2013 [inline] __x64_sys_accept+0x7d/0x90 net/socket.c:2013 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x58/0x100 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x4315f9 Code: fd ff 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 ab b4 fd ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffdb26d9c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002b RAX: ffffffffffffffda RBX: 0000000000400300 RCX: 00000000004315f9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000004 RBP: 00000000006e1018 R08: 0000000000400300 R09: 0000000000400300 R10: 0000000000400300 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000040cdf0 R14: 000000000040ce80 R15: 0000000000000055 </TASK> The reproducer invokes shutdown() before entering the listener status. After commit 94062790aedb ("tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets"), the above causes the child to reach the accept syscall in FIN_WAIT1 status. Eric noted we can relax the existing assertion in __inet_accept() 2024-08-23 CVE-2024-36484 openEuler-22.03-LTS-SP1 Low 3.9 AV:L/AC:H/PR:H/UI:N/S:U/C:L/I:L/A:L kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: add missing firmware sanity checks Add the missing sanity checks when parsing the firmware files before downloading them to avoid accessing and corrupting memory beyond the vmalloced buffer. 2024-08-23 CVE-2024-36880 openEuler-22.03-LTS-SP1 Medium 6.3 AV:L/AC:L/PR:H/UI:N/S:U/C:H/I:H/A:L kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when devlink reload during initialization The devlink reload process will access the hardware resources, but the register operation is done before the hardware is initialized. So, processing the devlink reload during initialization may lead to kernel crash. This patch fixes this by registering the devlink after hardware initialization. 2024-08-23 CVE-2024-36900 openEuler-22.03-LTS-SP1 Medium 4.4 AV:L/AC:L/PR:H/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: tcp: Use refcount_inc_not_zero() in tcp_twsk_unique(). Anderson Nascimento reported a use-after-free splat in tcp_twsk_unique() with nice analysis. Since commit ec94c2696f0b ("tcp/dccp: avoid one atomic operation for timewait hashdance"), inet_twsk_hashdance() sets TIME-WAIT socket's sk_refcnt after putting it into ehash and releasing the bucket lock. Thus, there is a small race window where other threads could try to reuse the port during connect() and call sock_hold() in tcp_twsk_unique() for the TIME-WAIT socket with zero refcnt. If that happens, the refcnt taken by tcp_twsk_unique() is overwritten and sock_put() will cause underflow, triggering a real use-after-free somewhere else. To avoid the use-after-free, we need to use refcount_inc_not_zero() in tcp_twsk_unique() and give up on reusing the port if it returns false. [0]: refcount_t: addition on 0; use-after-free. WARNING: CPU: 0 PID: 1039313 at lib/refcount.c:25 refcount_warn_saturate+0xe5/0x110 CPU: 0 PID: 1039313 Comm: trigger Not tainted 6.8.6-200.fc39.x86_64 #1 Hardware name: VMware, Inc. VMware20,1/440BX Desktop Reference Platform, BIOS VMW201.00V.21805430.B64.2305221830 05/22/2023 RIP: 0010:refcount_warn_saturate+0xe5/0x110 Code: 42 8e ff 0f 0b c3 cc cc cc cc 80 3d aa 13 ea 01 00 0f 85 5e ff ff ff 48 c7 c7 f8 8e b7 82 c6 05 96 13 ea 01 01 e8 7b 42 8e ff <0f> 0b c3 cc cc cc cc 48 c7 c7 50 8f b7 82 c6 05 7a 13 ea 01 01 e8 RSP: 0018:ffffc90006b43b60 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff888009bb3ef0 RCX: 0000000000000027 RDX: ffff88807be218c8 RSI: 0000000000000001 RDI: ffff88807be218c0 RBP: 0000000000069d70 R08: 0000000000000000 R09: ffffc90006b439f0 R10: ffffc90006b439e8 R11: 0000000000000003 R12: ffff8880029ede84 R13: 0000000000004e20 R14: ffffffff84356dc0 R15: ffff888009bb3ef0 FS: 00007f62c10926c0(0000) GS:ffff88807be00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020ccb000 CR3: 000000004628c005 CR4: 0000000000f70ef0 PKRU: 55555554 Call Trace: <TASK> ? refcount_warn_saturate+0xe5/0x110 ? __warn+0x81/0x130 ? refcount_warn_saturate+0xe5/0x110 ? report_bug+0x171/0x1a0 ? refcount_warn_saturate+0xe5/0x110 ? handle_bug+0x3c/0x80 ? exc_invalid_op+0x17/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? refcount_warn_saturate+0xe5/0x110 tcp_twsk_unique+0x186/0x190 __inet_check_established+0x176/0x2d0 __inet_hash_connect+0x74/0x7d0 ? __pfx___inet_check_established+0x10/0x10 tcp_v4_connect+0x278/0x530 __inet_stream_connect+0x10f/0x3d0 inet_stream_connect+0x3a/0x60 __sys_connect+0xa8/0xd0 __x64_sys_connect+0x18/0x20 do_syscall_64+0x83/0x170 entry_SYSCALL_64_after_hwframe+0x78/0x80 RIP: 0033:0x7f62c11a885d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a3 45 0c 00 f7 d8 64 89 01 48 RSP: 002b:00007f62c1091e58 EFLAGS: 00000296 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000020ccb004 RCX: 00007f62c11a885d RDX: 0000000000000010 RSI: 0000000020ccb000 RDI: 0000000000000003 RBP: 00007f62c1091e90 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000296 R12: 00007f62c10926c0 R13: ffffffffffffff88 R14: 0000000000000000 R15: 00007ffe237885b0 </TASK> 2024-08-23 CVE-2024-36904 openEuler-22.03-LTS-SP1 High 7.0 AV:L/AC:H/PR:L/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Skip on writeback when it's not applicable [WHY] dynamic memory safety error detector (KASAN) catches and generates error messages "BUG: KASAN: slab-out-of-bounds" as writeback connector does not support certain features which are not initialized. [HOW] Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK. 2024-08-23 CVE-2024-36914 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: nsh: Restore skb->{protocol,data,mac_header} for outer header in nsh_gso_segment(). syzbot triggered various splats (see [0] and links) by a crafted GSO packet of VIRTIO_NET_HDR_GSO_UDP layering the following protocols: ETH_P_8021AD + ETH_P_NSH + ETH_P_IPV6 + IPPROTO_UDP NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls skb_mac_gso_segment() to invoke inner protocol GSO handlers. nsh_gso_segment() does the following for the original skb before calling skb_mac_gso_segment() 1. reset skb->network_header 2. save the original skb->{mac_heaeder,mac_len} in a local variable 3. pull the NSH header 4. resets skb->mac_header 5. set up skb->mac_len and skb->protocol for the inner protocol. and does the following for the segmented skb 6. set ntohs(ETH_P_NSH) to skb->protocol 7. push the NSH header 8. restore skb->mac_header 9. set skb->mac_header + mac_len to skb->network_header 10. restore skb->mac_len There are two problems in 6-7 and 8-9. (a) After 6 & 7, skb->data points to the NSH header, so the outer header (ETH_P_8021AD in this case) is stripped when skb is sent out of netdev. Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH), skb_pull() in the first nsh_gso_segment() will make skb->data point to the middle of the outer NSH or Ethernet header because the Ethernet header is not pulled by the second nsh_gso_segment(). (b) While restoring skb->{mac_header,network_header} in 8 & 9, nsh_gso_segment() does not assume that the data in the linear buffer is shifted. However, udp6_ufo_fragment() could shift the data and change skb->mac_header accordingly as demonstrated by syzbot. If this happens, even the restored skb->mac_header points to the middle of the outer header. It seems nsh_gso_segment() has never worked with outer headers so far. At the end of nsh_gso_segment(), the outer header must be restored for the segmented skb, instead of the NSH header. To do that, let's calculate the outer header position relatively from the inner header and set skb->{data,mac_header,protocol} properly. [0]: BUG: KMSAN: uninit-value in ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline] BUG: KMSAN: uninit-value in ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline] BUG: KMSAN: uninit-value in ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668 ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline] ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668 ipvlan_start_xmit+0x5c/0x1a0 drivers/net/ipvlan/ipvlan_main.c:222 __netdev_start_xmit include/linux/netdevice.h:4989 [inline] netdev_start_xmit include/linux/netdevice.h:5003 [inline] xmit_one net/core/dev.c:3547 [inline] dev_hard_start_xmit+0x244/0xa10 net/core/dev.c:3563 __dev_queue_xmit+0x33ed/0x51c0 net/core/dev.c:4351 dev_queue_xmit include/linux/netdevice.h:3171 [inline] packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3081 [inline] packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook mm/slub.c:3819 [inline] slab_alloc_node mm/slub.c:3860 [inline] __do_kmalloc_node mm/slub.c:3980 [inline] __kmalloc_node_track_caller+0x705/0x1000 mm/slub.c:4001 kmalloc_reserve+0x249/0x4a0 net/core/skbuff.c:582 __ ---truncated--- 2024-08-23 CVE-2024-36933 openEuler-22.03-LTS-SP1 Medium 5.3 AV:L/AC:L/PR:L/UI:N/S:U/C:L/I:L/A:L kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved:bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueueFix NULL pointer data-races in sk_psock_skb_ingress_enqueue() whichsyzbot reported [1].[1]BUG: KCSAN: data-race in sk_psock_drop / sk_psock_skb_ingress_enqueuewrite to 0xffff88814b3278b8 of 8 bytes by task 10724 on cpu 1: sk_psock_stop_verdict net/core/skmsg.c:1257 [inline] sk_psock_drop+0x13e/0x1f0 net/core/skmsg.c:843 sk_psock_put include/linux/skmsg.h:459 [inline] sock_map_close+0x1a7/0x260 net/core/sock_map.c:1648 unix_release+0x4b/0x80 net/unix/af_unix.c:1048 __sock_release net/socket.c:659 [inline] sock_close+0x68/0x150 net/socket.c:1421 __fput+0x2c1/0x660 fs/file_table.c:422 __fput_sync+0x44/0x60 fs/file_table.c:507 __do_sys_close fs/open.c:1556 [inline] __se_sys_close+0x101/0x1b0 fs/open.c:1541 __x64_sys_close+0x1f/0x30 fs/open.c:1541 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75read to 0xffff88814b3278b8 of 8 bytes by task 10713 on cpu 0: sk_psock_data_ready include/linux/skmsg.h:464 [inline] sk_psock_skb_ingress_enqueue+0x32d/0x390 net/core/skmsg.c:555 sk_psock_skb_ingress_self+0x185/0x1e0 net/core/skmsg.c:606 sk_psock_verdict_apply net/core/skmsg.c:1008 [inline] sk_psock_verdict_recv+0x3e4/0x4a0 net/core/skmsg.c:1202 unix_read_skb net/unix/af_unix.c:2546 [inline] unix_stream_read_skb+0x9e/0xf0 net/unix/af_unix.c:2682 sk_psock_verdict_data_ready+0x77/0x220 net/core/skmsg.c:1223 unix_stream_sendmsg+0x527/0x860 net/unix/af_unix.c:2339 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x140/0x180 net/socket.c:745 ____sys_sendmsg+0x312/0x410 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x1e9/0x280 net/socket.c:2667 __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x46/0x50 net/socket.c:2674 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75value changed: 0xffffffff83d7feb0 -> 0x0000000000000000Reported by Kernel Concurrency Sanitizer on:CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024Prior to this, commit 4cd12c6065df ( bpf, sockmap: Fix NULL pointerdereference in sk_psock_verdict_data_ready() ) fixed one NULL pointersimilarly due to no protection of saved_data_ready. Here is anotherdifferent caller causing the same issue because of the same reason. Sowe should protect it with sk_callback_lock read lock because the writerside in the sk_psock_drop() uses write_lock_bh(&sk->sk_callback_lock); .To avoid errors that could happen in future, I move those two pairs oflock into the sk_psock_data_ready(), which is suggested by John Fastabend. 2024-08-23 CVE-2024-36938 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix seg fault in rxe_comp_queue_pkt In rxe_comp_queue_pkt() an incoming response packet skb is enqueued to the resp_pkts queue and then a decision is made whether to run the completer task inline or schedule it. Finally the skb is dereferenced to bump a 'hw' performance counter. This is wrong because if the completer task is already running in a separate thread it may have already processed the skb and freed it which can cause a seg fault. This has been observed infrequently in testing at high scale. This patch fixes this by changing the order of enqueuing the packet until after the counter is accessed. 2024-08-23 CVE-2024-38544 openEuler-22.03-LTS-SP1 Medium 4.7 AV:L/AC:H/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: eth: sungem: remove .ndo_poll_controller to avoid deadlocks Erhard reports netpoll warnings from sungem: netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398) WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c gem_poll_controller() disables interrupts, which may sleep. We can't sleep in netpoll, it has interrupts disabled completely. Strangely, gem_poll_controller() doesn't even poll the completions, and instead acts as if an interrupt has fired so it just schedules NAPI and exits. None of this has been necessary for years, since netpoll invokes NAPI directly. 2024-08-23 CVE-2024-38597 openEuler-22.03-LTS-SP1 Medium 4.4 AV:L/AC:L/PR:H/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find() Syzbot reports a warning as follows: ============================================ WARNING: CPU: 0 PID: 5075 at fs/mbcache.c:419 mb_cache_destroy+0x224/0x290 Modules linked in: CPU: 0 PID: 5075 Comm: syz-executor199 Not tainted 6.9.0-rc6-gb947cc5bf6d7 RIP: 0010:mb_cache_destroy+0x224/0x290 fs/mbcache.c:419 Call Trace: <TASK> ext4_put_super+0x6d4/0xcd0 fs/ext4/super.c:1375 generic_shutdown_super+0x136/0x2d0 fs/super.c:641 kill_block_super+0x44/0x90 fs/super.c:1675 ext4_kill_sb+0x68/0xa0 fs/ext4/super.c:7327 [...] ============================================ This is because when finding an entry in ext4_xattr_block_cache_find(), if ext4_sb_bread() returns -ENOMEM, the ce's e_refcnt, which has already grown in the __entry_find(), won't be put away, and eventually trigger the above issue in mb_cache_destroy() due to reference count leakage. So call mb_cache_entry_put() on the -ENOMEM error branch as a quick fix. 2024-08-23 CVE-2024-39276 openEuler-22.03-LTS-SP1 Medium 4.7 AV:L/AC:H/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved:jfs: xattr: fix buffer overflow for invalid xattrWhen an xattr size is not what is expected, it is printed out to thekernel log in hex format as a form of debugging. But when that xattrsize is bigger than the expected size, printing it out can cause anaccess off the end of the buffer.Fix this all up by properly restricting the size of the debug hex dumpin the kernel log. 2024-08-23 CVE-2024-40902 openEuler-22.03-LTS-SP1 High 7.8 AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: tty: add the option to have a tty reject a new ldisc ... and use it to limit the virtual terminals to just N_TTY. They are kind of special, and in particular, the "con_write()" routine violates the "writes cannot sleep" rule that some ldiscs rely on. This avoids the BUG: sleeping function called from invalid context at kernel/printk/printk.c:2659 when N_GSM has been attached to a virtual console, and gsmld_write() calls con_write() while holding a spinlock, and con_write() then tries to get the console lock. 2024-08-23 CVE-2024-40966 openEuler-22.03-LTS-SP1 Medium 4.7 AV:L/AC:H/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: ibmvnic: Add tx check to prevent skb leak Below is a summary of how the driver stores a reference to an skb during transmit: tx_buff[free_map[consumer_index]]->skb = new_skb; free_map[consumer_index] = IBMVNIC_INVALID_MAP; consumer_index ++; Where variable data looks like this: free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3] consumer_index^ tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null] The driver has checks to ensure that free_map[consumer_index] pointed to a valid index but there was no check to ensure that this index pointed to an unused/null skb address. So, if, by some chance, our free_map and tx_buff lists become out of sync then we were previously risking an skb memory leak. This could then cause tcp congestion control to stop sending packets, eventually leading to ETIMEDOUT. Therefore, add a conditional to ensure that the skb address is null. If not then warn the user (because this is still a bug that should be patched) and free the old pointer to prevent memleak/tcp problems. 2024-08-23 CVE-2024-41066 openEuler-22.03-LTS-SP1 Medium 6.4 AV:L/AC:H/PR:H/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: nvme: avoid double free special payload If a discard request needs to be retried, and that retry may fail before a new special payload is added, a double free will result. Clear the RQF_SPECIAL_LOAD when the request is cleaned. 2024-08-23 CVE-2024-41073 openEuler-22.03-LTS-SP1 Medium 6.4 AV:L/AC:H/PR:H/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved:ata: libata-core: Fix double free on errorIf e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jumpto the err_out label, which will call devres_release_group().devres_release_group() will trigger a call to ata_host_release().ata_host_release() calls kfree(host), so executing the kfree(host) inata_host_alloc() will lead to a double free:kernel BUG at mm/slub.c:553!Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTICPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014RIP: 0010:kfree+0x2cf/0x2f0Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 daRSP: 0018:ffffc90000f377f0 EFLAGS: 00010246RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0PKRU: 55555554Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? die+0x2e/0x50 ? do_trap+0xca/0x110 ? do_error_trap+0x6a/0x90 ? kfree+0x2cf/0x2f0 ? exc_invalid_op+0x50/0x70 ? kfree+0x2cf/0x2f0 ? asm_exc_invalid_op+0x1a/0x20 ? ata_host_alloc+0xf5/0x120 [libata] ? ata_host_alloc+0xf5/0x120 [libata] ? kfree+0x2cf/0x2f0 ata_host_alloc+0xf5/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci]Ensure that we will not call kfree(host) twice, by performing the kfree()only if the devres_open_group() call failed. 2024-08-23 CVE-2024-41087 openEuler-22.03-LTS-SP1 High 7.8 AV:L/AC:L/PR:L/UI:N/S:U/C:H/I:H/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: can: mcp251xfd: fix infinite loop when xmit fails When the mcp251xfd_start_xmit() function fails, the driver stops processing messages, and the interrupt routine does not return, running indefinitely even after killing the running application. Error messages: [ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16 [ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3). ... and repeat forever. The issue can be triggered when multiple devices share the same SPI interface. And there is concurrent access to the bus. The problem occurs because tx_ring->head increments even if mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX package while still expecting a response in mcp251xfd_handle_tefif_one(). Resolve the issue by starting a workqueue to write the tx obj synchronously if err = -EBUSY. In case of another error, decrement tx_ring->head, remove skb from the echo stack, and drop the message. [mkl: use more imperative wording in patch description] 2024-08-23 CVE-2024-41088 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers register store validation for NFT_DATA_VALUE is conditional, however, the datatype is always either NFT_DATA_VALUE or NFT_DATA_VERDICT. This only requires a new helper function to infer the register type from the set datatype so this conditional check can be removed. Otherwise, pointer to chain object can be leaked through the registers. 2024-08-23 CVE-2024-42070 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: powerpc: Avoid nmi_enter/nmi_exit in real mode interrupt. nmi_enter()/nmi_exit() touches per cpu variables which can lead to kernel crash when invoked during real mode interrupt handling (e.g. early HMI/MCE interrupt handler) if percpu allocation comes from vmalloc area. Early HMI/MCE handlers are called through DEFINE_INTERRUPT_HANDLER_NMI() wrapper which invokes nmi_enter/nmi_exit calls. We don't see any issue when percpu allocation is from the embedded first chunk. However with CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK enabled there are chances where percpu allocation can come from the vmalloc area. With kernel command line "percpu_alloc=page" we can force percpu allocation to come from vmalloc area and can see kernel crash in machine_check_early: [ 1.215714] NIP [c000000000e49eb4] rcu_nmi_enter+0x24/0x110 [ 1.215717] LR [c0000000000461a0] machine_check_early+0xf0/0x2c0 [ 1.215719] --- interrupt: 200 [ 1.215720] [c000000fffd73180] [0000000000000000] 0x0 (unreliable) [ 1.215722] [c000000fffd731b0] [0000000000000000] 0x0 [ 1.215724] [c000000fffd73210] [c000000000008364] machine_check_early_common+0x134/0x1f8 Fix this by avoiding use of nmi_enter()/nmi_exit() in real mode if percpu first chunk is not embedded. 2024-08-23 CVE-2024-42126 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: drm/lima: fix shared irq handling on driver remove lima uses a shared interrupt, so the interrupt handlers must be prepared to be called at any time. At driver removal time, the clocks are disabled early and the interrupts stay registered until the very end of the remove process due to the devm usage. This is potentially a bug as the interrupts access device registers which assumes clocks are enabled. A crash can be triggered by removing the driver in a kernel with CONFIG_DEBUG_SHIRQ enabled. This patch frees the interrupts at each lima device finishing callback so that the handlers are already unregistered by the time we fully disable clocks. 2024-08-23 CVE-2024-42127 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: mm: avoid overflows in dirty throttling logic The dirty throttling logic is interspersed with assumptions that dirty limits in PAGE_SIZE units fit into 32-bit (so that various multiplications fit into 64-bits). If limits end up being larger, we will hit overflows, possible divisions by 0 etc. Fix these problems by never allowing so large dirty limits as they have dubious practical value anyway. For dirty_bytes / dirty_background_bytes interfaces we can just refuse to set so large limits. For dirty_ratio / dirty_background_ratio it isn't so simple as the dirty limit is computed from the amount of available memory which can change due to memory hotplug etc. So when converting dirty limits from ratios to numbers of pages, we just don't allow the result to exceed UINT_MAX. This is root-only triggerable problem which occurs when the operator sets dirty limits to >16 TB. 2024-08-23 CVE-2024-42131 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: libceph: fix race between delayed_work() and ceph_monc_stop() The way the delayed work is handled in ceph_monc_stop() is prone to races with mon_fault() and possibly also finish_hunting(). Both of these can requeue the delayed work which wouldn't be canceled by any of the following code in case that happens after cancel_delayed_work_sync() runs -- __close_session() doesn't mess with the delayed work in order to avoid interfering with the hunting interval logic. This part was missed in commit b5d91704f53e ("libceph: behave in mon_fault() if cur_mon < 0") and use-after-free can still ensue on monc and objects that hang off of it, with monc->auth and monc->monmap being particularly susceptible to quickly being reused. To fix this: - clear monc->cur_mon and monc->hunting as part of closing the session in ceph_monc_stop() - bail from delayed_work() if monc->cur_mon is cleared, similar to how it's done in mon_fault() and finish_hunting() (based on monc->hunting) - call cancel_delayed_work_sync() after the session is closed 2024-08-23 CVE-2024-42232 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: Prevent OOB read/write in usb_string_copy() Userspace provided string 's' could trivially have the length zero. Left unchecked this will firstly result in an OOB read in the form `if (str[0 - 1] == '\n') followed closely by an OOB write in the form `str[0 - 1] = '\0'`. There is already a validating check to catch strings that are too long. Let's supply an additional check for invalid strings that are too short. 2024-08-23 CVE-2024-42236 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: ext4: make sure the first directory block is not a hole The syzbot constructs a directory that has no dirblock but is non-inline, i.e. the first directory block is a hole. And no errors are reported when creating files in this directory in the following flow. ext4_mknod ... ext4_add_entry // Read block 0 ext4_read_dirblock(dir, block, DIRENT) bh = ext4_bread(NULL, inode, block, 0) if (!bh && (type == INDEX || type == DIRENT_HTREE)) // The first directory block is a hole // But type == DIRENT, so no error is reported. After that, we get a directory block without '.' and '..' but with a valid dentry. This may cause some code that relies on dot or dotdot (such as make_indexed_dir()) to crash. Therefore when ext4_read_dirblock() finds that the first directory block is a hole report that the filesystem is corrupted and return an error to avoid loading corrupted data from disk causing something bad. 2024-08-23 CVE-2024-42304 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes In cdv_intel_lvds_get_modes(), the return value of drm_mode_duplicate() is assigned to mode, which will lead to a NULL pointer dereference on failure of drm_mode_duplicate(). Add a check to avoid npd. 2024-08-23 CVE-2024-42310 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031 In the Linux kernel, the following vulnerability has been resolved: bna: adjust 'name' buf size of bna_tcb and bna_ccb structures To have enough space to write all possible sprintf() args. Currently 'name' size is 16, but the first '%s' specifier may already need at least 16 characters, since 'bnad->netdev->name' is used there. For '%d' specifiers, assume that they require: * 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8 * 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX is 16 And replace sprintf with snprintf. Detected using the static analysis tool - Svace. 2024-08-23 CVE-2024-43839 openEuler-22.03-LTS-SP1 Medium 5.5 AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H kernel security update 2024-08-23 https://www.openeuler.org/zh/security/security-bulletins/detail/?id=openEuler-SA-2024-2031